There is a specific kind of frustration unique to robot vacuum owners. The machine itself is invisible most of the time — it lives under the sofa and only appears at 2am to announce that it has found a sock. But the dock does not move. It sits there in the hallway with its little water tanks and its dust bag, and it is the single object in your home that looks like it belongs in a laboratory rather than a living room. If you have ever found yourself moving a table slightly to the left every time you vacuum so the robot can reach its charger, you already know that the dock placement is a design decision, not an afterthought. This guide covers nine ways to hide a robot vacuum and its dock without a full renovation, and the measurements that decide which idea will actually work in your home.
Quick Answer: The Numbers That Matter
- Robot height: 95 mm (3.74 in) on the Freo 20, Freo 20 Edge and Flow 2; 109.6 mm (4.3 in) on the Freo Z10 Ultra.
- Clear floor in front of the dock: 0.45 m minimum, straight from Narwal's user manuals. Aim for 60–90 cm if your layout allows.
- Maintenance access: the dust bag and both water tanks must be reachable by hand, without moving furniture.
- Position: decide where the dock will live before the first map, because moving a base station afterwards means rebuilding the map.
1. Measure Before You Design
Every hiding idea in this guide is built around the same set of physical dimensions. Get these wrong and a beautiful cabinet becomes a robot that cannot reach its charger. Get them right and the choice of idea comes down to taste.
| Measurement | What it is | Why it matters when you build a hiding spot |
|---|---|---|
| Robot height | 95 mm (3.74 in) on Freo 20, Freo 20 Edge and Flow 2; 109.6 mm (4.3 in) on Freo Z10 Ultra | Sets the minimum internal height of any shelf, plinth void or hollowed furniture you cut for the robot |
| Dock footprint | Flow 2: 450 × 360 × 530 mm; Freo 20: 431 × 402 × 461 mm; Freo 20 Edge: 360 × 450 × 530 mm; Freo Z10 Ultra: 430.8 × 462 × 388.3 mm | Sets the size of the cabinet recess. A 45 cm-wide base cabinet is tight for the Flow 2 |
| Front clearance | 0.45 m minimum, per the Flow 2 and Freo 20 user manuals | The single most common reason a "hidden" dock ends up standing in the open |
| Access height | Dust bag bay, clean water tank and dirty water tank are reached from the top of the dock | Decides between a top-loading design (needs vertical room) and a front-loading design (needs a hinged flap) |
| Heat output | Mop washing up to 100°C (212°F); drying at 60°C (140°F) on the Freo 20, 45°C (113°F) on the Freo 20 Edge and 40°C (104°F) on the Flow 2 | Determines how much ventilation gap you must leave behind and above the enclosure |
| Power | Power cord plugs into the rear of the dock and runs to a wall outlet | You need a socket inside or immediately behind the enclosure, plus a routing path that does not cross the robot's entry lane |
0.45 m is the floor, not the target
A robot that can technically dock but cannot comfortably turn around will bump, retry and eventually give up — and a robot that fails to dock is the single most common complaint in why a robot vacuum stops returning to its dock. Treat 45 cm as the absolute minimum and 90 cm as the comfortable target.
One structural detail is worth planning around early: the dock is filled from the top. You lift a cover, lift the clean water tank out, refill it and drop it back in. That means your enclosure needs a lift-up flap or a removable top panel with clearance above it — and ideally a flap that hinges at the back so it does not swing into the robot's parking space.
2. The 9 Hiding Ideas, Ranked by Difficulty
All nine keep the dock powered, ventilated and reachable. They differ in how much carpentry they need, how much they hide, and how much they risk frustrating the robot. Difficulty is rated as a weekend project with basic tools.
Idea 1 — Flip-Up Door in a Base Cabinet (Best Overall)
A standard base cabinet door is replaced with a hinge-up flap that lifts vertically. The dock sits on the cabinet base behind it, and the robot drives out through the opening. Because the flap hinges backwards, it stays out of the robot's path and does not need a wide swing.
- Needs: a base cabinet at least 50 cm wide and 55 cm deep, a concealed or piano hinge, and a soft-close strut so the flap does not crash down.
- Watch out: the flap edge must not rub the robot's top sensors or catch the mop pad as it leaves. Trim the leading edge and test with the robot docked before you finish painting.
- Also: route the power cord through a rear notch in the cabinet, not through the door gap, so the cable is never pinched.
Idea 2 — Toe-Kick Plinth Void in a Cabinet Run
The most discreet option on this list, and the one that looks the least like "a place where a robot lives". The recessed plinth along the bottom of your kitchen cabinets is exactly the right height for the robot, and you only need to remove one or two toe-kick panels and extend the void along the run.
- Needs: a plinth void at least 110 mm tall for the Freo 20 / Flow 2 and 120 mm for the Freo Z10 Ultra, with the dock positioned so the robot drives straight out into the room.
- Watch out: the robot's front bumper and cameras need to see the room. Keep the plinth line open rather than boxing the robot in with a fascia board.
- Also: keep the floor under the plinth level. A robot that docks on a slight slope often needs several attempts before it settles.
Idea 3 — Freestanding Pantry or Larder Unit
A full-height cupboard with a door that looks like any other cupboard door. The dock goes on the bottom shelf, the water tanks pull out at the bottom, and the robot has a doorway to come and go through.
- Needs: a socket inside the unit (not behind it), a levelled base, and a door that opens wide enough for the robot to pass with the full approach lane clear.
- Watch out: this is the option where airflow is most likely to be a problem. Cut a vent grille in the door or the top panel, and check that the door can stay ajar during a wash-and-dry cycle.
- Also: if you want the robot to leave while the door is shut, the doorway must be flush with the floor or have a low ramp — a 20 mm lip is enough to stop some robots entirely.
Idea 4 — Hollowed Side Table or Nightstand
The cheapest good-looking option. Take a small side table or a slim nightstand, remove the bottom shelf, and leave the top surface as a completely normal table. The dock sits inside, the robot drives out from the open underside.
- Needs: at least 130 mm of internal height for the robot's 95 mm body plus the dock's own risers, and a footprint wide enough for the dock.
- Watch out: a hollowed nightstand needs to be stable — if the robot bumps the frame while docking, the whole table rocks and the robot may never settle.
- Also: add a rear cable channel so the cord runs down the back leg and out at floor level rather than across the floor.
Idea 5 — Storage Ottoman with Raised Legs
Flip the idea: instead of hollowing furniture, raise it. An empty storage ottoman with 140–150 mm of leg clearance works as a cover, and the robot drives underneath it. Because the interior is empty and ventilated, the heat issue is largely solved.
- Needs: short legs or a plinth base with 140–150 mm of clearance, a removable fabric or wooden base panel, and enough flat floor beneath for the robot to align with the dock.
- Watch out: a thick upholstered skirt will brush the robot's sides as it enters. Cut the hem back or use a low-profile trim.
- Also: this option hides the robot completely, which means you lose the visual confirmation that it is charging. Check status from the app rather than by looking.
Idea 6 — Faux Planter Box
A wooden enclosure with a hinged front panel, finished to look like a large planter, with a real or artificial plant on top. It moves well in a hallway, an entryway or a living room corner, and it looks completely deliberate rather than apologetic.
- Needs: a water-resistant base sealed from the floor, and a solid top panel that can take the weight of a planted pot.
- Watch out: a hinged front door that swings outward into the robot's path. Hinge it on the far side or use a lift-off panel instead.
- Also: if you use a real plant, remember the watering. Nobody wants a waterlogged oak planter next to a 100°C mop-washing cycle.
Idea 7 — Under-Stair Cupboard (Best in a Hallway)
The void under a staircase is a natural cavity: it is already enclosed, already out of the way, and usually near a wall socket. A slim cabinet installed in the low end of the stair run gives you a dock home that takes up zero floor space.
- Needs: enough depth at the low end for the dock footprint, and a socket within reach.
- Watch out: the stair structure restricts ventilation. This is a spot where a vent grille in the door matters more than anywhere else in the house.
- Also: remember the robot still cannot climb stairs. Hiding the dock under the stairs does not extend its range — for that you need to think about how robot vacuums handle stairs and high thresholds and where the robot is carried.
Idea 8 — Appliance Garage or Laundry Alcove with a Sliding Door
If you already have a tall appliance housing — the kind with a sliding or lift-up panel that hides the washer, the dryer or the bin — the dock can share it. The sliding door solves the swing problem entirely, because it parks flat against the side wall.
- Needs: a vented panel, a socket, and enough depth for the dock plus the robot's approach.
- Watch out: a sliding door that runs across the floor track can become an obstacle for the robot's bumper and side brush. Choose a trackless or recessed track.
- Also: check the floor level inside the housing. Appliance housings often sit on a slightly raised plinth, and a robot that cannot dock on a slope will keep retrying.
Idea 9 — Media Console or TV Cabinet with a Vented Door
The idea that gets shared most often online and the one most likely to fail — but it works if you build it properly. The robot docks inside a media unit, the front has a perforated or slatted panel, and the console's own height clearance does the hiding.
- Needs: 120 mm of internal height for the robot, a ventilated front panel, and space in front for the approach lane — which in a media unit usually means the whole front bay has to stay open.
- Watch out: cables. Media units are cable-dense, and a robot that works its way through a nest of HDMI leads will get tangled. If you already have this problem, read whether you need to pick everything up before running a robot vacuum.
- Also: the console must not be a closed box if the dock's heat output is trapped. Perforated door or leave a rear gap.
3. The Nine Ideas at a Glance
| Idea | Best for | Difficulty | How well it hides | Main risk |
|---|---|---|---|---|
| 1. Flip-up cabinet door | Kitchens and utility rooms with a base cabinet | Medium | Excellent | Flap edge catching the robot or mop pad |
| 2. Toe-kick plinth void | Modern kitchens with a continuous plinth | Low | Best of all | Only works if the plinth run is already deep enough |
| 3. Pantry / larder unit | Homes with a utility or boot room | Medium | Excellent | Ventilation inside a closed cupboard |
| 4. Hollowed side table | Living rooms and bedrooms, tight budgets | Low | Good | Internal height and table stability |
| 5. Raised-leg ottoman | Living rooms with soft seating | Very low | Good | Upholstered skirt brushing the robot |
| 6. Faux planter box | Hallways, entryways, corners | Medium | Excellent | Hinged door swinging into the exit path |
| 7. Under-stair cupboard | Hallways and staircases | Medium | Excellent | Restricted airflow under the stairs |
| 8. Appliance garage | Homes with a laundry or utility housing | Low | Excellent | Floor track and plinth height |
| 9. Media console | Open-plan living rooms | High | Fair | Cables, and only 120 mm of usable height |
4. Three Complete Room Recipes
The nine ideas above are components. Below are three finished schemes that combine them into a single coherent look, because the difference between "a robot vacuum hidden behind a door" and "a home that looks like it was designed by someone who does not own a robot vacuum" is entirely in the consistency of the details.
Recipe A — Scandinavian Minimal (White Oak, Matte White, Hidden Hardware)
- Structure: toe-kick plinth void (Idea 2) along the kitchen run, with a matching oak fascia and no visible hinges.
- The dock bay: painted matte white to match the toe-kick, with the robot driving straight out into the room at floor level.
- Detail work: white cable channel running inside the plinth so not one centimetre of cord is visible; a flat brushed-metal socket plate instead of a white plastic one.
- Why it works: the robot becomes part of the architecture. Nothing in the room looks like it exists to store an appliance.
Recipe B — Warm Nordic Living Room (Soft Textiles, Oak, Cream)
- Structure: a raised-leg storage ottoman (Idea 5) acting as a coffee-table-adjacent seat, plus a hollowed side table (Idea 4) in the corner for the dock.
- Colour: cream bouclé on the ottoman, white oak legs, and a natural jute rug that stops 5 cm short of the ottoman so the robot has a hard surface to dock on.
- Detail work: the ottoman base panel lifts off with a magnetic catch rather than a hinge, so there are no visible fixings.
- Why it works: the dock is inside a piece the room wanted anyway, and the soft furnishings are exactly the surfaces you would rather not mop over with a robot-driven mop.
Recipe C — Small Flat or Rented Home (No Drilling, No Renovation)
- Structure: a faux planter box (Idea 6) beside the entry, or a hollowed IKEA-style nightstand (Idea 4) if you are renting.
- Non-invasive: no wall cutting, no plumbing changes. A socket-mounted extension point or a surface-mounted trunking keeps the cord invisible without chasing it into the wall.
- Detail work: the planter is painted the same colour as the skirting board, and the robot docks on a small rigid mat rather than directly on carpet — carpet under a dock is one of the reasons robot vacuums on carpet can take longer to charge and lose alignment.
- Why it works: nothing is fixed to the wall, so the setup moves with you and can be undone in an afternoon.
5. Power, Heat and Water
Hiding the dock is only half the job. The things that make a robot vacuum setup look like one are the cord, the mismatched panel, and the hard edge where the robot emerges. The functional side — power, heat and water — is where enclosures quietly fail.
Route the cord so it never crosses the exit lane
The power cord plugs into the rear of the dock, which means it can run directly up the back of whatever enclosure you build and out through a rear notch or grommet. It should never run along the floor in front of the dock, and it should never pass under a door where it can be pinched. If your socket is far away, a surface-mounted trunking channel in matching colour is far better than a loose cable — and a cable crossing the robot's path is exactly the kind of thing that ends with the robot snagged on a charge lead while you are on a call.
Cord checklist
- Exit the enclosure at the back, level with the socket.
- Leave a little slack so the plug is not the thing under tension when the robot bumps the dock.
- Use a socket plate or a matching trunking cover — not a white plastic extension box.
- Never run the cord through the door hinge or across the robot's entry line.
- Check the cable is not pinched when the flap closes; test it closed and open before you seal the cabinet.
Give the wash-and-dry system air
A self-cleaning dock boils water and then blows hot air at a damp mop for an hour. Seal it inside a closed box and you are creating a warm, humid microclimate with wet fabric in it — which is how you get musty odours and mould around the mop pads, the exact problem the wash-and-dry cycle exists to prevent. Practical mitigations:
- Leave a 3–5 cm gap behind and above the dock, inside the enclosure.
- Install a slotted or perforated panel on the door or side, not a solid one.
- Where the design allows, let the door stand ajar or the top panel sit slightly offset during wash-and-dry cycles.
- Empty the dirty water tank after every mopping run. A closed enclosure hides the smell until it does not.
- Run a wash-and-dry cycle when the enclosure is open, or set the drying cycle to a shorter duration in the app.
If your hiding spot has to be airtight — a fitted pantry, a closed appliance garage — then the dock model matters. The Freo 20 Edge dries at a lower temperature than the Freo 20 and the Flow 2, which makes it the more forgiving unit to enclose.
Where the water and the power actually go
If you are considering the optional auto refill and drainage system for the Flow 2 — the version that plumbs fresh water in and dirty water out to a sink or drainage point — then the hiding spot and the plumbing have to be designed together. An under-sink cabinet becomes the natural home, because the supply and waste lines are already there. This is the one scenario where "hiding" genuinely improves the installation rather than complicating it, and it is worth reading about how robot vacuum water refill and drainage systems actually work before you plan the cabinet.
For every other setup, the socket question is the simple one: install a socket inside or immediately behind the enclosure, positioned so the dock's rear power cord reaches it without a visible run of cable. Some electrical work needs a qualified electrician — that is not a robot vacuum decision, it is a household electrical one.
Two things that go wrong inside a hiding spot
1. A closed door while the robot is docking. Many flaps cannot be closed with the robot present, and forcing it damages the bumper or the hinge. Decide in advance whether the flap stays open during cleaning or whether the robot docks to an open bay.
2. Trapped humidity. A sealed cupboard around a 60°C drying cycle is a mould risk. Vents are not optional.
6. Do Not Forget the Robot's Exit Path
Every idea in this guide conceals the dock. The robot itself still drives around your home in the open, and it still needs to leave and return. Two failure modes account for most "the robot won't come home" complaints in hidden-dock setups:
- The doorway is blocked or too narrow. The robot needs a clear, level path out of the enclosure and the full approach lane in front of the dock. This is also where the threshold question from can robot vacuums climb stairs and high thresholds becomes relevant — a standard robot handles a single step of roughly 2 cm, but a badly finished cabinet threshold can easily be worse than that. Build the threshold flush or ramped rather than relying on the robot's climbing ability.
- The robot cannot see out. Cameras and LiDAR need a view of the room to navigate away from the dock. If your enclosure wraps the robot in dark, reflective or fully enclosed surfaces, it may sit and wait rather than launch. Leave the opening at the front of the bay completely unobstructed.
There is a second, subtler point worth making: hiding the dock does not reduce the robot's cleaning area. Some people assume a concealed dock means the robot has to find its way out of a cupboard each run, which they assume reduces coverage. It does not, but a badly designed enclosure does add several seconds of manoeuvring noise on every single run — which is exactly the kind of thing you notice when you are trying to keep the machine quiet during a video call. If noise is a factor in your setup, the decibel figures matter more than the cabinet joinery, and they are covered in robot vacuum coverage, noise and multi-floor performance.
7. Choose the Dock's Position Before You Build
Narwal's manuals are explicit on this point: once mapping is finished, do not move the dock, otherwise you need to rebuild the map. If you relocate the base station after mapping, the robot's understanding of where "home" is stops matching reality, and it will start driving to the wrong coordinates in rooms it used to know perfectly. That is why the final position has to be chosen before the cabinet is installed, not after. If you have already hit this, the fixes are in how to manage Narwal maps, no-go zones and cleaning zones in the app.
Design order that avoids a rebuild
- Choose the room and the wall the dock will live on — permanently.
- Run the robot once in that spot and complete the initial mapping run.
- Only then measure the space and build or buy the enclosure around it.
- If a cabinet is already installed, plan to keep the dock in the same physical spot and hide it with a removable cover rather than relocating it.
8. Before You Build: A 10-Minute Checklist
- Measure the robot and the dock against the table in section 1.
- Mark out 0.45 m in front of the intended position and check nothing in that zone has to live — no chair legs, no bin, no shoes.
- Confirm the socket position and the cord exit route before you order a cabinet.
- Check the floor level. Use a spirit level; a dock on a slope causes repeated failed docking.
- Decide how the enclosure opens — top-lift or front-hinge — based on how the tanks and dust bag come out.
- Plan the ventilation before the panels are cut, not after.
- Check the threshold. Any lip between the floor and the docking bay should be flush or ramped.
- Finish mapping before you enclose the dock.
- Test the flap with the robot docked before the final coat of paint.
- Plan the maintenance rhythm. One to two-weekly access to the dust bag and both water tanks, without moving furniture.
9. Frequently Asked Questions
Can I hide the dock completely, with no door visible at all?
Yes, if you use a plinth void (Idea 2) or an open-sided ottoman (Idea 5). Both conceal the dock without a door that has to be opened. The trade-off is that you cannot see the charging status light, so check the app instead. If you want to keep the status light visible, a slatted or perforated door works well — the dock's indicator is still readable through the gaps.
How much space does the robot need in front of the dock?
Narwal's user manuals specify a clear space of at least 0.45 m (about 18 in) in front of the charging dock so the robot can enter and exit freely. In practice, aim for 60–90 cm of open floor if your layout allows, so the robot has room to align and turn without bumping the enclosure. If it keeps failing to dock, the first thing to check is whether that lane is clear.
Can I put the dock inside a closed cabinet with a wash-and-dry function?
Only with ventilation. Mop washing heats water to up to 100°C (212°F) and drying runs at up to 60°C (140°F) on the Freo 20, 45°C (113°F) on the Freo 20 Edge and 40°C (104°F) on the Flow 2. Leave a 3–5 cm gap behind and above, use a perforated or slotted panel, keep the dirty water tank empty, and let the enclosure breathe during a wash-and-dry cycle. The Freo 20 Edge is the more forgiving unit if the space is genuinely tight.
What if I already mapped the house and now want to move the dock?
You will need to rebuild the map. Narwal's manuals state that the dock should not be moved after mapping is finished, otherwise the map must be recreated. If the dock has to move, set it in its final position, clear the area around it, and run a fresh mapping pass. If you have hit a problem since moving it, the recovery steps are in the fixes for a robot vacuum that will not return to its dock.
Is it worth hiding the dock at all?
Worth it if the dock currently sits in a doorway, a main hallway or the middle of the living room, because those are the positions where the robot gets bumped and the dock gets kicked. If the dock is already in a quiet corner, a simpler solution is a cable channel and a fabric cover over the cord run. For anyone still deciding what to buy, the comparison in how to choose a robot vacuum is a better use of time than the joinery, and whether a robot vacuum actually saves time or just adds chores is an honest read on whether the whole category suits your home.
Design Your Setup
Compact docks, low-profile bodies and self-cleaning wash-and-dry cycles — built to live in a cabinet, a plinth or a corner you actually want to look at.
Browse Robot Vacuums

